Adjustable Pedestal Clever
What is tokoz Clever?
These are raised and plastic flooring pedestals used in terraces that may or may not be walked on. They are designed to reach the desired final elevation and eliminate the difference in slope. Their purpose is to enable making the last layer of flooring without using protective alum on the insulation. These pedestals also aim to provide a continuous drainage system through the open joint gaps of the floor tiling. Adjus- table plastic flooring pedestals offer a system that can be intervened under potential insulation problems, which are also quite durable with a minimum carrying capacity of 500 kg.
The screwed part protrusion of the Head part is fastened to the gap in the adjustment stud wall. This prevents passing the safe level of elevation while adjus- ting in the application process. In this way, the application pro- cess is up to the standards and the users‘ safety is guaranteed.
Edges and corners may lead to extra consumptions. Adjus- table TOKOZ works with a jack system and can be used as a single part in edges and corners. So, in proportion to space width, consumption is decreased.
In this process, fundamentally, an adjustment gasket and joint stick with ten different types are required. Angular placement is possible, depending on the floor plan.
T-ST
T-ST
The joint stick and its 2, 4, 6 and 8 mm of width alternatives can be rotated 360 degrees around their axis. The length of these products is 16 mm and has an alterna- tive type with a length of 38 mm and a width of 4 mm.
T-ST
T-ST
The joint stick and its 2, 4, 6 and 8 mm of width alternatives can be rotated 360 degrees around their axis. The length of these products is 16 mm and has an alterna- tive type with a length of 38 mm and a width of 4 mm.
T-AFJ
T-AFJ
This product is used in tile floorings. It is usually preferred for specific details where pedestal connection via screws is desired. The joint pieces can be broken down into pieces for tricky floors and edges.
T-AFJ
T-AFJ
This product is used in tile floorings. It is usually preferred for specific details where pedestal connection via screws is desired. The joint pieces can be broken down into pieces for tricky floors and edges.
T-UWS
T-UWS
Tiles may be blown away due to wind. T-UWS prevents this and allows the system to work as a whole. Used with the T-AFJ accessory, it is attached to the pedestal via screws, and ties the pressed CP-GP product to the system to support the tile flooring. It can be screwed with an Allen key and allows the flooring material to be lifted from the pedestal together with CP-GP. Flooring material can be re-assembled in the same way.
T-UWS
T-UWS
Tiles may be blown away due to wind. T-UWS prevents this and allows the system to work as a whole. Used with the T-AFJ accessory, it is attached to the pedestal via screws, and ties the pressed CP-GP product to the system to support the tile flooring. It can be screwed with an Allen key and allows the flooring material to be lifted from the pedestal together with CP-GP. Flooring material can be re-assembled in the same way.
T-SP
T-SP
The joint stick with a plus sign shape is placed on the central gap of the head part and has a width of 4 mm. This product is designed to be broken down into pieces which allows it to be used easily in tricky floorings. This product increases the speed of the process.
T-SP
T-SP
The joint stick with a plus sign shape is placed on the central gap of the head part and has a width of 4 mm. This product is designed to be broken down into pieces which allows it to be used easily in tricky floorings. This product increases the speed of the process.
T-UW
T-UW
Tiles may be blown away due to wind. T-UW prevents this and allows the system to work as a whole. Used with the T-AFJ accessory, it is attached to the pedestal via screws. It has a cover that conceals the screw. This cover can be removed from the piece for dismantling purposes.
T-UW
T-UW
Tiles may be blown away due to wind. T-UW prevents this and allows the system to work as a whole. Used with the T-AFJ accessory, it is attached to the pedestal via screws. It has a cover that conceals the screw. This cover can be removed from the piece for dismantling purposes.
T-WS
T-WS
T-WS prevents light tile vibrations and enables the system to work as a whole. Used with the T-AFJ accessory, it is attached to the pedestal via screws. It allows the tiles to be removed by the Allen key. Tiles can be re-assembled in the same way.
T-WS
T-WS
T-WS prevents light tile vibrations and enables the system to work as a whole. Used with the T-AFJ accessory, it is attached to the pedestal via screws. It allows the tiles to be removed by the Allen key. Tiles can be re-assembled in the same way.
C-S
C-S
This product is designed with 1-, 2-, 3- and 4-mm alternatives and made of TPE raw material. It aims to eliminate the calibration problems usually encountered in tile flooring products. It is used between the tile and the pedestal and absorbs the impact vibration. It is recommended that this product is used in each pedestal module. T-S can be broken into four pieces.
C-S
C-S
This product is designed with 1-, 2-, 3- and 4-mm alternatives and made of TPE raw material. It aims to eliminate the calibration problems usually encountered in tile flooring products. It is used between the tile and the pedestal and absorbs the impact vibration. It is recommended that this product is used in each pedestal module. T-S can be broken into four pieces.
T-AP
T-AP
T-AP is used to connect the pedestal and CP-P1 and equivalent skeletons, which are used to support tile and lath floorings. Skeletons are attached to the piece by clicking.
T-AP
T-AP
T-AP is used to connect the pedestal and CP-P1 and equivalent skeletons, which are used to support tile and lath floorings. Skeletons are attached to the piece by clicking.
T-AR
T-AR
This skeleton assembly apparatus can be assembled into any gap of the head part except for the central one, and it can be rotated 360 degrees around its axis. Screwing is possible due to holes on the sides of the product. With this product, all skeletons from 1 cm to 10 cm can be used.
T-AR
T-AR
This skeleton assembly apparatus can be assembled into any gap of the head part except for the central one, and it can be rotated 360 degrees around its axis. Screwing is possible due to holes on the sides of the product. With this product, all skeletons from 1 cm to 10 cm can be used.
T-AW
T-AW
The circle-shaped skeleton assembly apparatus is first assembled to the skeleton via a screwdriver with distances written in the specifications. Later, it is placed in the central gap of the head part together with the skeleton. Skeletons of any size including and bigger than 1 cm can be used with this product.
T-AW
T-AW
The circle-shaped skeleton assembly apparatus is first assembled to the skeleton via a screwdriver with distances written in the specifications. Later, it is placed in the central gap of the head part together with the skeleton. Skeletons of any size including and bigger than 1 cm can be used with this product.
T-DCN
T-DCN
for Deck flooring:
It is designed to attach the natural deck to the skeleton. It has a conical shape which minimizes the weakening and breaking of deck flooring channels and prevents the connecting screws from being visible from the joint places.
T-DCN
T-DCN
for Deck flooring:
It is designed to attach the natural deck to the skeleton. It has a conical shape which minimizes the weakening and breaking of deck flooring channels and prevents the connecting screws from being visible from the joint places.
T-DC
T-DC
It is designed to attach the composite and natural deck floorings to the skeleton.
T-DC
T-DC
It is designed to attach the composite and natural deck floorings to the skeleton.
C-SL :
Slope Corrector Head eliminates the effects of the slopes (up to 7%) created for drainage and enables an even ground.
C-SLH :
With its moving head, it eliminates any ground-based slope up to 7%.
C-SLB :
By placing them on the head part, a ground for the C-SLH piece can be obtained. When placed on grounds with a slope of up to 7%, the C-SLH piece enables them to be even.
T-P :
Orthopedic Base Pad made of TPE raw material can be used in floors with faulty polish, and it absorbs impact vibrations that can occur in the system. It has a width of 5 mm.
Clever Edge End Support
Used for supporting smaller tiles in the edges. It can be moved in one direction on the pedestal and can support different sized tile pieces.
CP-F1-1
CP-F1-2
CP-F1-3
C-F0 : It has a height of 3 mm. It is designed so that a single joint piece can be separated by breaking for tricky floorings. It can be made of soft raw material, which allows floorings on pebbles.
C-F1 : It has a height of 15 mm. It can be separated into four parts which prevents extra consumption in edges and corners.
C-FS : This product is designed with 1- and 2-mm alternatives and made of TPE raw material. It aims to eliminate the calibration problems usually encountered in tile flooring products. It is used between the tile and the pedestal and absorbs the impact vibration. It is recommended that this product is used in each pedestal module. C-FS can be broken into four pieces.
C-F2: It has a height of 20 mm. It can be separated into four parts which prevents extra consumption in edges and corners.
C-F3: It has a height of 25 mm. It can be separated into four parts for edges and corners. With its moving head, it can absorb the vibrations caused by the defects on the ground. Same efficacy can be acquired by using it on the adjusted products.
C-F4: It has a height of 50 mm. It can be separated into four parts which prevents extra consumption in edges and corners.
English 
Türkçe 
Deutsch 
Français 
Español 
Русский 
العربية 
Kurmanci